|
No pee
Mar 19, 2024 15:59:49 GMT -5
Post by finatic on Mar 19, 2024 15:59:49 GMT -5
I changed the impellers and water pumps in November just fired up the motors after sitting 5 months. And no pee from both motors WTF,,, any suggestions I really don't want to drop them.
|
|
|
No pee
Mar 19, 2024 16:15:14 GMT -5
Post by fishnfool on Mar 19, 2024 16:15:14 GMT -5
Both motors?
Usual cause is not getting the shaft into the hole which would require dropping the lowers and getting the drive shaft in that hole.
|
|
|
No pee
Mar 19, 2024 17:11:52 GMT -5
Post by finatic on Mar 19, 2024 17:11:52 GMT -5
It has to be in there every thi g lined up perfectly. I did need help with the port side.
|
|
|
Post by finatic on Mar 19, 2024 18:06:27 GMT -5
I'm thinking because I used a different water and hose supply it wasn't supplying enough water. Tomorrow I'll use an outside water source with a bigger hose. Exterior water is still off for the winter🤞.
|
|
|
Post by abouttime2fish on Mar 19, 2024 18:54:04 GMT -5
Here in NC it’s usually those stupid mud daubers plugging the hole. I’ve found 400# leader works well to clear, but any plastic stick about 12 inches long. Works best with water on.
|
|
|
No pee
Mar 19, 2024 20:01:40 GMT -5
Post by fishnfool on Mar 19, 2024 20:01:40 GMT -5
Here in NC it’s usually those stupid mud daubers plugging the hole. I’ve found 400# leader works well to clear, but any plastic stick about 12 inches long. Works best with water on. I didn't even thing about that, they hit me every year too. I need to run 100+ lb mono up there to clear it out. Very annoying when I get to the ramp and no pee.
|
|
Deleted
Deleted Member
Posts: 0
|
No pee
Mar 20, 2024 7:01:41 GMT -5
Post by Deleted on Mar 20, 2024 7:01:41 GMT -5
Fin, Gerry rig up a garden hose "y-valve". Attach the flushing muffs on one outlet of the "y-valve" and attach to the gear case. Run a short piece of hose off the the other "y-valve" outlet and connect to to your motor's flush port. Turn on the water, start the motor, then trim up the motor about a third while its running. The 150's can be a bit touchy getting a solid stream out of the water as its a pressure thing. Trimming up the motor along with added water pressure is the ticket. Cheers Pete
|
|
|
No pee
Mar 20, 2024 9:04:46 GMT -5
Post by outtadblue on Mar 20, 2024 9:04:46 GMT -5
My guess is not enough water pressure. I don’t have enough pressure at the marina but if I bring it home and hook it up I have plenty pressure to make it pee.
|
|
|
Post by finatic on Mar 20, 2024 14:47:05 GMT -5
My guess is not enough water pressure. I don’t have enough pressure at the marina but if I bring it home and hook it up I have plenty pressure to make it pee. AND you win the prize, o shit we can't accept them only give them away. I used a different water supply and all is good. I gave myself an O shit moment last night, I should know better.
|
|
|
Post by timing on Mar 21, 2024 6:59:12 GMT -5
My guess is not enough water pressure. I don’t have enough pressure at the marina but if I bring it home and hook it up I have plenty pressure to make it pee. AND you win the prize, o shit we can't accept them only give them away. I used a different water supply and all is good. I gave myself an O shit moment last night, I should know better. good to hear no engine cooling system issues
|
|